Browse + Post a Listing

CAT 3516E 2800 KW 50 Hz 400 V

ReflowX SKU: REF-892

whatsapp Whatsapp

Description

General Information:

  • Model: Caterpillar CAT 3516E
  • Power Output: 2800 kW (2.8 MW) per engine
  • Frequency: 50 Hz (for global power generation)
  • Voltage: 400V (Nominal)
  • Hours of Operation: Only 300 hours since new – these engines are essentially like new, with minimal wear.
  • Quantity Available: 3 units available for sale
  • Fuel Type: Diesel (Typically used with diesel fuel but can be modified to operate with other fuels such as gas with modifications)
  • Cooling System: Water-cooled engine (closed-loop system for temperature control)
  • Condition: Used but with only 300 operational hours, in near-new condition
  • Delivery: Immediate delivery upon agreement

Engine Specifications:

  • Engine Configuration:
    • Cylinder Configuration: V16
    • Cylinder Bore: 170 mm (6.69 inches)
    • Stroke: 190 mm (7.48 inches)
    • Total Displacement: 78.7 L (4,805 cubic inches)
    • Compression Ratio: 16.5:1
    • Aspiration: Turbocharged with aftercooler for enhanced performance and efficiency
    • Cycle: Four-stroke
  • Rated Speed: 1500 RPM (for the generation of 50 Hz electrical power)
  • Lubrication: Full-flow filtration system with bypass
  • Governor Type: Electronic (for precise speed and load control)
  • Exhaust Temperature: Approximately 450-500°C under full load

Performance Characteristics:

  • Maximum Power Output: 2800 kW (2.8 MW) at 1500 RPM (nominal)
  • Fuel Consumption: Typically around 198–210 g/kWh at full load, which is typical for a diesel engine of this size
  • Max Torque: 1,825 Nm at 1,200 RPM
  • Operational Efficiency: Designed for high fuel efficiency with reduced emissions at full load
  • Power Factor: Can operate at a 0.8 power factor, suitable for industrial power generation.

Electrical Characteristics:

  • Output Voltage: 400 V (nominal)
  • Frequency: 50 Hz
  • Connection: 3-phase system
  • Generator Type: Typically paired with synchronous or asynchronous generators
  • Alternator Rated Power: 2800 kW at 0.8 power factor
  • Output Characteristics: Stable and high-quality power for critical systems
  • Harmonic Distortion: Low, designed for sensitive electronics in industrial and commercial applications

Fuel System:

  • Fuel Type: Diesel (typically #2 diesel, but can be configured to handle other fuels like heavy fuel oil (HFO) with modifications)
  • Fuel Tank Capacity: Varies depending on configuration and desired run time between refueling
  • Fuel Filters: Primary and secondary fuel filters to ensure clean fuel delivery to the engine
  • Fuel Consumption: Around 198-210 g/kWh depending on load

Cooling System:

  • Cooling Type: Water-cooled (closed-loop system for high reliability)
  • Coolant Capacity: Approximately 300–400 liters (dependent on setup)
  • Water Pump: High-efficiency pump for coolant circulation
  • Exhaust Heat Recovery: May include systems for utilizing exhaust heat for other plant processes, improving overall system efficiency

Dimensions and Weight:

  • Length: Approximately 4,800 mm (189 inches)
  • Width: Approximately 2,200 mm (87 inches)
  • Height: Approximately 2,400 mm (94 inches)
  • Weight: Around 23,000 kg (50,700 lbs) per engine (without generator set)

Electrical & Control Systems:

  • Governor System: Electronic governor (provides precise load and speed control)
  • Engine Control Module (ECM): Equipped with the Cat EMCP (engine monitoring and control panel) for real-time data, diagnostics, and management
  • Monitoring System: Includes diagnostics for oil pressure, fuel flow, exhaust temperatures, and more
  • Safety Features: Overspeed protection, low oil pressure shutdown, high-temperature shutdown, and more
  • Automatic Load Acceptance: Can automatically adjust power output to meet load demands

Exhaust System:

  • Exhaust Gas Temperature: Typically 450-500°C at full load, designed for high-efficiency combustion
  • Exhaust Treatment: Includes SCR (Selective Catalytic Reduction) or other technologies to meet regional emissions standards
  • Turbocharged and Aftercooled: Enhances engine performance, reduces exhaust temperatures, and increases efficiency.

Maintenance and Service:

  • Oil Change Interval: Typically 500-1000 hours (depending on the operational environment)
  • Major Overhaul: Typically 15,000-20,000 hours before major engine overhaul, depending on the operational load and conditions
  • Routine Maintenance: Regular maintenance includes checking fuel filters, oil filters, coolant levels, and performing diagnostic tests.

Environmental Compliance:

  • Emissions: Designed to meet Tier 2 or Tier 3 emissions standards (depending on region and specific model configuration)
  • NOx, CO, CO2: Equipped with systems for emission reduction, including after-treatment systems if necessary
  • Noise Levels: Low noise design for industrial and commercial use with soundproofing options available.

Applications:

  • Power Generation: Ideal for base-load or emergency power generation in both industrial and commercial applications.
  • Marine: Can be used for marine propulsion applications with necessary modifications.
  • Prime or Standby Power: Suitable for facilities that require reliable and continuous or backup power, including manufacturing plants, data centers, and hospitals.
  • Remote or Off-grid Locations: Can provide power to remote locations where grid power is unavailable.

Summary of Key Specifications:

  • Model: CAT 3516E
  • Output Power: 2800 kW (2.8 MW) per engine
  • Frequency: 50 Hz
  • Voltage: 400 V
  • Configuration: V16, turbocharged, aftercooled
  • Total Hours: Only 300 hours since new, very low usage
  • Fuel Consumption: 198–210 g/kWh (at full load)
  • Weight: 23,000 kg (50,700 lbs) per engine
  • Cooling: Water-cooled system
  • Quantity Available: 3 units
  • Delivery: Immediate

Price: Upon Request – The price details can be provided directly by the seller.

Availability: Immediate Delivery – The engines are ready for shipment upon agreement.

For further specifications or to inquire about this equipment and ReflowX's logistics services, Please contact ReflowX at info@reflowx.com 

 

Supporting Documents

General Terms

  • ReflowX and the seller retain the right to evaluate and approve offers.
  • Buyers should verify quantities and conditions upon delivery.
  • After successful engagement, both buyer and seller manage communication for payment terms and delivery schedule.
  • All parties agree to adhere to ReflowX Terms and Conditions in transactions.
  • Buyers can request value-added services such as pre-purchase inspections, Expediting & Delivery Services through ReflowX. Contact us!
British Owned Company ISO
Reflowx

Transforming procurement for the Energy Sectors Contact us for Sustainable Solutions. Dubai Internet City- United Arab Emirates

Quick Links

Contact Us

Address UAE

Office 002,
Ground Floor,
Sheikh Mohammed,
Bin Zayed Rd,
Dubai Production City,
UAE

Address UK

Office 61,
Fordwell Road,
Fairfield,
Stockton-on-Tees,
UK

© ReflowX2024 - All Rights Reserved
ariba